進入展臺 在線留言

歡迎聯系我

有什么可以幫您？在線咨詢

破裂強度試驗機顯示板使用說明書



資料類型


文件大小


瀏覽次數
3322次


上傳時間
2008年12月27日

關鍵詞: 破裂機,拉力機,環壓機

上傳者: 東莞市高鑫檢測設備有限公司

資料簡介

FA1761F/FA3861F USER’S GUIDE P.0

Table of contents

■General description--------------------------------------------------------------------1

■FA1761F--------------------------------------------------------------------------------------1

■FA3861F--------------------------------------------------------------------------------------1

■Common specifications--------------------------------------------------------------1

■Dimension of FA1761F----------------------------------------------------------------2

■Dimension of FA3861F----------------------------------------------------------------2

■Installation ---------------------------------------------------------------------------------2

■Illustration of front panel----------------------------------------------------------- 3

■Installation place----------------------------------------------------------------------- 4

■Installation method------------------------------------------------------------------------------- 4

■Power line and ground connections ----------------------------------------- 4

■ON/OFF output and PID control output connections----------------- 5

■Communication connections----------------------------------------------------- 5

■Initial set------------------------------------------------------------------------------------ 6

■Key functions in running------------------------------------------------------------ 6

■Over temp. display----------------------------------------------------------------------7

■Under temp. display--------------------------------------------------------------------7

■ON/OFF of key-lock---------------------------------------------------------------------7

■Auto-tuning---------------------------------------------------------------------------------7

■PID control display---------------------------------------------------------------------7FA1761F/FA3861F USER’S GUIDE P.1

General description

The FA1761F/FA3861F is a temperature- humidity controller for the dry/wet bulb system without transducer。

FA1761F

Name ：Temperature controller

Model ：FA1761F（Recorder output include）

Input ：Pt100Ω

Accuracy：±0.3℃

Setting range：SCLL -99.0~0.0℃

SCLH 10.0~200.0℃

Display range：-99.9~210.0℃

FA3861F

Name ：Humidity controller

Model ：FA3861F（Recorder output include）

Input ：Pt100Ω

Accuracy：±1％

Setting range：SCLL 0.0~40.0﹪

SCLH 60.0~100.0﹪

Common specifications

Display：PV 8㎜ red LED

SV 8㎜ green LED

（7 segments，4 character positions）

Display cycle：1 sec.

Control：PID（SSR） + ON/OFF + ON/OFF

Output ：PID output－SSR

ON/OFF output－relay contact output

Action mode：reverse（low）/direct（high）

Proportional band：0.0~50.0℃/﹪

Integral time：0~99min.59 sec.

Derivative time：0~99min.59sec.

Control cycle：1~30 sec.

Hysteresis of alarm：0.1~ 2.5℃/﹪

Deviation setting：±30.0℃/﹪

Recorder output：SCLL~SCLH──DC 4~20mA

Power voltage：AC100 / 110V ±10﹪or

AC200 / 220V ±10﹪ 50 / 60Hz 4VA

Memory backup：approx.10 years（at 23℃±2℃，55±10％RH，for standard model）

Dimensions：（H）96 （W）48 （D）129㎜

Panel cutout：（H）90±0.5 （W）43±0.5㎜

Weight：approx.500g

Standard Accessory：mounting 2pcs/1set

FA1761F/FA3861F USER’S GUIDE P.2

Dimension of FA1761F

Dimension of FA3861F

Installation

■1 set ■N sets

FA1761F/FA3861F USER’S GUIDE P.3

Illustration of front panel

（1） 4 character red LED：Display of PV。When we want to key-in a value，the position glittered with this value. If display＝HHHH，it means the present value（PV）is higher than 『SCLH』；If display＝LLLL，it means the present value（PV）is lower than 『SCLL』。

（2） 4 character green LED：Display of SV。When we want to key-in a value，the position glittered with this value.SV and percent of PID output are changeable。

（3） Display of output1：Light lamped when output1 is ON。

（4） Display of output2：Light lamped when output2 is ON。

（5） Display of output3：Light lamped when output3 is ON。

（6） Display of communication：It’ll check automatically once every second.（Communicate status between FA1761F and FA3861F），if the status is OK，it glittered with lamp。

（7） Function key：We can change the display mode by pressing this key。

（8） Left key：For input position moving。

（9） Up key：Increase value or function select。

（10） Down key：Reduce value or function select。

（11） Unit：Temperature（FA1761F）-℃；Humidity（FA3861F）-﹪。

FA1761F/FA3861F USER’S GUIDE P.4

Installation place

■Place where an ambient temperature is 0 to 40℃，and relative humidity is 80﹪RH or less。

■Place where no water splash and non-condensing develop。

■Place where no direct sunshine exist。

■Place where is clear and dust or corrosive gas are not present。

■Place where is far from noise-generating devices such as heavy duty solenoid switches and phase control SCRs。

Installation method

■Insert the FA1761F/FA3861F unit from through the cutout on the panel。

■Secure two claws of the mounting brackets to the holes on the side panel of the unit。

■Tighten the screws for the mounting brackets to secure the units。

Power line and ground connections

■The power line and ground connections are made at the FA1761F/FA3861F’s terminal board。

■The FA1761F/FA3861F is designed to operate on 100/110VAC or 200/220VAC 50/60Hz power line。

■Make sure to connect the G（ground）terminal to the earth to minimize external interference。

■For AC100V or AC110V。 ■For AC200V or AC220V。

FA1761F/FA3861F USER’S GUIDE P.5

ON/OFF output and PID control output connections

Communication connections

FA1761F/FA3861F USER’S GUIDE P.6

Initial set

This item contains setting range selection、offset adjust、action mode selection（reverse or direct）。

The initial set display is shown from the normal display by simultaneously pressing the two keys： and for a while，at the same time，PID output＝OFF。

Under this status，It will change by pressing key in sequence as below：

Display	Name	Function
SCLL	Scale Low	The low limit value of setting for Temp. or Humi.
SCLH	Scale High	The high limit value of setting for Temp. or Humi.
oFFS	Offset Adjust	Range：±5.0。 Example：If deviation value＝+1，input value＝-1。
cycL	Cycle Time	Range：1~30 sec.。
LMTL	Limit Low	The low limit value of PID output。 Range：0~30。
LMTH	Limit High	The high limit value of PID output。 Range：70~100。
PID	PID Zone	The cut point of PID zone。（2 parts）
SEt	Set Method	AbSo(Absolute)/DeviationdEU1 selection of output2 and output3。
oPEr	Operate Mode	cont(Control)/ALAr(Alarm) selection of output2 and output3。
out1	Out1	HigH(High)/Louu(Low) selection of output1。
out2	Out2	HigH(High)/Louu(Low) selection of output2。（When operate mode＝Alarm，it decided automatically）
out3	Out3	HigH(High)/Louu(Low) selection of output3。（When operate mode＝Alarm，it decided automatically）
uuEt	Wet	Temperature display of wet bulb。
Loc	Loc	Lock function selection。
tyPE	Type	Display of controller’s model。

Key functions in running

Green LED：It will change by pressing key in sequence as below：（In running）
→Set1→Pb L→It L→dt L→Pb H→It H→dt H→Set2→diF2→SEt3→diF3

FA1761F/FA3861F USER’S GUIDE P.7

Display	Name	Function
SEt1	Set 1	Setting of output1
Pb L	Proportional Band Low	Setting of P（Low）
It L	Reset Time Low	Setting of I（Low）
dt L	Reset Time Low	Setting of d（Low）
Pb H	Proportional Band High	Setting of P（High）
It H	Reset Time High	Setting of I（High）
dt H	Reset Time High	Setting of d（High）
SEt2	Set 2	Setting of output2
diF2	Differential Gap2	Hysteresis of output2
SEt3	Set 3	Setting of output3
diF3	Differential Gap3	Hysteresis of output2

■ Setting range of P：0.0~50.0 deg / ﹪。

■ Setting range of I and D：0.00~99.59(0~99min.59sec.)

■ Setting range of differential gap：0.1~2.5 deg / ﹪。

Over temp.display

It will show the error message as below：HHHH ，at the same time，PID output＝OFF。

Under temp.display

It will show the error message as below：LLLL ，at the same time，PID output＝OFF。

ON/OFF of key-lock

We can change the key lock ON/OFF from the normal display by simultaneously pressing the two keys： and for a while。

Auto-tuning

We can change the auto-tuning ON/OFF from the normal display by simultaneously pressing the two keys： and for a while。

PID control display

We can change the setting value/percent of PID output from the normal display by simultaneously pressing the two keys： and for a while。

相關產品

免責聲明

凡本網注明“來源：儀表網”的所有作品，均為浙江興旺寶明通網絡有限公司-儀表網合法擁有版權或有權使用的作品，未經本網授權不得轉載、摘編或利用其他方式使用上述作品。已經本網授權使用作品的，應在授權范圍內使用，并注明“來源：儀表網”。違反上述聲明者，本網將追究其相關法律責任。
本網轉載并注明自其他來源（非儀表網）的作品，目的在于傳遞更多信息，并不代表本網贊同其觀點和對其真實性負責，不承擔此類作品侵權行為的直接責任及連帶責任。其他媒體、網站或個人從本網轉載時，必須保留本網注明的作品第一來源，并自負版權等法律責任。
如涉及作品內容、版權等問題，請在作品發表之日起一周內與本網聯系，否則視為放棄相關權利。